AURA 1

16 audio, 16 GPIO, 4 AES, IP, 2 RS, 1 HD SDI

Overview

The AUDIO RACER is the compact and efficiency solution for the transmission of commodities signals and also signals for the photo director, over optical fibers, between OB truck and stage. One link offers the transmission of the following signals:

  • 16 analog and bidirectional audio channels,
  • 16 General purpose input / output,
  • 4 bidirectional AES links ‘’protocol_less’’ on one coaxial cable each,
  • 1 Ethernet 10/100Mbs, 2 RJ45 port on two VLAN.
  • 2 RS 422/485 channels.
  • 1 bidirectional HDSDI signal.

The products are in a 19″ 1U chassis rack, with forced air cooling controlled in temperature.

 

Real time, low delay

In order to avoid any audio noticeable delay for the staff working on stage, the AUDIO RACER analog and AES audio processing features :

  • Synchronism of the sampling frequencies of the signals.
  • Clock management at receiver side to synchronize the clock with the return channel.

Thus enabling a no buffer transmission with delay kept as minimum.

 

Supervising

One http server is integrated in the AUDIO RACER, it delivers the status of the equipment on web page interface. The available information includes technical information of the product (internal voltages, internal temperature, optical status…) and also signals information (signal presence, data setting). The RJ45 of the “AUDIO” VLAN gives the access to the server.

 

Signaling

To facilitate installation/trouble shoot process, the AUDIO RACER features on the front face full information LED status, displaying all signal presence and technical alarms of the product.

No external diagnostic equipment is required at first start.

Video SD/HD

Number, connector: 1 bidirectional channel on BNC
Impedance: 75 Ω
Standard: SDI, ASI, HD, (2HD optional, specific optical component)
Amplitude: Input: cable equalization (140 m Belden 1694A for HD), Output: 800mV pp
Return loss: Better than -15 dB

 

Analog Audio

Number: 16 bidirectional channels, on 4 SUB-D 25 sockets
Impedance: Input: 10 KΩ differential (non floating), Output: 20 Ω differential (non floating)
Amplitude: +4 dBm nominal (saturation at + 18 dBm)
Bandwidth: 50 Hz to 15 KHz at +/- 0.5dB, (20Hz to 20 KHz at -3dB)
Distortion: 0.05% at 1KHz +18 dBm
Signal to noise ratio: 90dB, “A” weighted
Signaling threshold: -15 dBm on inputs / -15 dBFS on outputs
Delay: 380 microseconds

 

Audio AES

Number: 4 channels, each channel is bidirectional on one BNC
Impedance: 75 Ω
Amplitude: 1.5 Volts peak to peak
Gigue: 0.02UI RMS / 0.04UI peak to peak (Audio signal at 48 KHz)
Delay: 1.8 microseconds

 

Data

Number: 2 bidirectional channels, 1 SUB-D 9 sockets connector per channel
Protocols: RS485, RS422, RS232
Data rate: 0 to 230 Kbd/s
Setting: A coding wheel at front face of AUDIO RACER for each signal (RS 485 2 wires by bonding on SUB-D)

 

Ethernet

Number: 2 channels separate by internal VLAN
Connector: RJ45 (Auto MDI)
Protocols: 10 or 100mb/s, Full or Half-duplex (Auto), MDI or MDI-X (Auto)

 

GPIO

Number: 16 GPIO, on 2 connectors SUB-D 37 sockets
Output: Relay (dry contact). ‘Common’ – ‘Normally Open’ terminals for each relay
Input: Opto-coupler, Command 5 to 24 volts non polarized, Built in current limitation
Delay: 3ms Typical ( Time for relay switching)

 

Power supply

Consumption: 20 Watts per rack
Voltage: 115V or 230VAC (+10, -15%) 50-60Hz, internal switch selection
Type: Redundancy PSU

 

Mechanical

Dimensions: 19″ 1U chassis rack
Cooling: One fan with speed management

 

Signaling

2 x Video: Video presence (2 LED)
16 x Analog audio: Inputs: Audio presence (16 LED), Outputs: audio presence (16 LED)
4 x AES: Inputs: Audio presence (4 LED), Outputs: audio presence (4 LED)
2 x Ethernet: “Link” and “activity” (4 LED)
2 x RS 422, 485: “Rx” and “Tx” (4 LED)
16 x GPIO: Status of the relay (16 LED), Status of the input (16 LED)
Optical: Optical receiver status, optical component alarm, optical fiber alarm
Power supply: “ON” (indicates internal voltage are OK)